its one of 2 ways to hook it up. Our customers were recording studios, nightclubs, and touring bands. Actually i use it to run four Three way Pioneer 6.5 speakers nice sound.

Some cars these days don't have a ACC cable so if you're car doesn't have that you want to get an amp that can detect if the car is on/off via the speaker feed itself.

If our price drops after you buy, call us.

Power Harness: The included power harness plugs into a pigtail You need to match your AMP to your SPEAKERS. I installed one in a 95 Jeep Wrangler and another one in a 1990 Mitsubishi Eclipse. depending on year that can be perplexing.

Fits in the glove box !

.This amp will surprise you. But if you had an inline fuse as close as possible to the battery, you'd be protected. Since 1974. I use a set of 6.5 inch components(pioneer) and they play loud without distortion even with volume turned up to max, Great match for ur 6inch speakers..I power a pair of 6.5 components and a 6.75inch kicker sub with this amp..been using this amp without any problems for bout 2yrs now...great buy and sounds awesome..good luck. Soft turn-on and turn-off circuitry prevents potentially damaging thumps to your system as it powers on or off. Best bass systems for your small car or hatchback. XC1410 amplifier pdf manual download. Speaker Level Inputs: The speaker-level inputs are 9-1/2" I was worried that it might get too hot and cut out but so far it hasn't. plug one end of wire to front red/white and the same on back of radio.

If you want more control over this look for a head unit with per channel EQ. Awesome experience with Crutchfield. crossover slope is 12 dB/octave. 50 Watts RMS, Its just what comes out of the amp also i was not impressed with this amp my suggestion is go with a 400watt amp 4ch i am very impress with the results of that. Fuses never hurt to have either Especially if you don't want to replace your battery and wires. Bypass the clarion with the sub out. Judy, This will be based on available diagrams and length of your factory HU harness.

It doesn't have its own Bluetooth or USB. 4-Channel amplifier; 40-amp ATO fuse (installed in-line) 9" Power/Ground harness; 9" Speaker-level output harness; Four 3/4" Self-tapping screws; 4 Flat washers; Owner's manual (English/ French/ Spanish) Warranty information; Featured review. Our Vehicle Research Team has taken apart and measured over 28,000 vehicles. power wire should be connected directly to the battery, so it will likely need to be extended; Clarion recommends 10-gauge as the minimum power and ground wire size. Fits in the glove box ! For the price they are clean crisp and loud! Not meant for home; it's designed on a 12V system. - 83 answers, http://www.crutchfield.com/Support/Bio.aspx?bio=5. This is just one of the solutions for you to be successful. As long as your pre amp conections are RCA jax this amp should work fine. Calls may be recorded for training and quality control purposes. http://crutchfield.custhelp.com/app/answers/list/kw/. All in all I was very happy and impressed with the amp and would definitely buy it again. Also l connected a separate amp for a 8 inch kicker and run a hi/low converter to the deck. Crutchfield is servicemark of Crutchfield Corporation. this unit does not have a switch to change it from 2 channel to 4 channel, its strictly meant for 4 speakers. I've been very pleased with the sound quality and functionality of this amp. They will be able to pull up your vehicle and give you the details on if this will fit and what you will need for an installation in your vehicle. Mine is mounted in a motorcycle fairing. You wil be able to retain the use of the fade and balance controls on your head unit. Match the RMS ratings, dont pay attention to PEAK power. Thanks for the excellent products and support.

Compact 4-channel car amplifier — 75 watts RMS x 4, Compact 4-channel amplifier — 45 watts RMS x 4. If you no longer wish to receive the call, please click the button to cancel your request. And Clarion managed to pack more watts per square inch inside the XC1410 than almost any other 4-channel amp made. there are 4 leads coming off the unit itself connected internally so the answer is no, unless you splice the rt front and rt rear leads together and do the same with the left side then it might work. Hz, 60 Hz, or Flat (the crossover is bypassed and the output is full range). The amplifier is going to level the input regardless of weather it's pre amp signal (rca) or speaker wire (high level input).

Dont run AMPS in series ! Additionally, there is only one gain switch for the unit, not one for the front and one for the rear -- the gain switch is used to switch the amp between high-level and rca-level inputs. Just the right amount of power for the wife ! 50 Watt RMS speakers will match to a 50 Watt RMS AMP etc.

Then just ran the rca's up to the loc and the control knob out. In an actual listening room, you'd find that some speakers play louder than others when fed the same amount of power. Hope this helps. Crutchfield: Audio, video, and more. am/fm cd player. Yes- that is what I did. It'll be overkill but there cheap due to being used on lots of 3D printers. If you look at the picture, see the wires that come out near the RCA leads ? I connected the amp to the outputs from the oem deck and power to battery. Friend bought same size alpine amp for his jeep with good results. good luck. 6-1/2" component speaker system - also fit 6-3/4" openings Please see our review guidelines for help and information.

But performance in the real world is affected by the acoustics of your car or home, your choice of amplification, and your source material. You'll appreciate the high-level inputs that give you the ability to hook this amp up to almost any system, even those like factory stereos without RCA-type connections. User Manuals, Guides and Specifications for your Clarion XC1410 Amplifier, Car Amplifier. This means that this amp can connect to a factory head unit or aftermarket head unit and you can still control the fade and balance. by Crutchfield's Our toll-free Tech Support number is printed on your invoice, and is also available under the "My Orders" tab in the "My Account" section of our website. This puts the load at 4 ohms Also this amp has a switch on it I do believe to block low frequency's from its output effectively blocking bass from your speakers. Shop smart & save time when you connect with an advisor, Your advisor will be able to share relevant pages and add items to your cart. I would highly suggest purchasing a vehicle specific wiring plug adapter. xmd1. They are low level inputs from the receiver. The XC1410 also has wires that you can go to your speaker wires. Easiest hook up there is. Does this amp have a remote turn on wire (aka blue wire?)